ASUS ML248H: Thin for the Win?

Introduction and Hardware Impressions
The stand for the ML248 is unlike any monitor stand I’ve seen before. Comprised of a pair of rings that lock together and then into the rear of the display, this allows for tilt and swivel adjustments but no height adjustment. It is dead simple to install, though, which is nice. The back of the display is a white plastic that stands out compared to the standard black, though likely it won’t be seen much of the time. Perhaps because of the slim profile of the display, there is only a single HDMI input and one D-sub input, but no DVI or DisplayPort inputs available. There is also a 3.5mm headphone jack for listening to audio carried over HDMI, but no integrated speakers or USB hub in the display. Of course if you were to wall mount this, good luck in getting to that headphone jack.

Gallery: ASUS ML248H Exterior

• 
• 
• 
• 
• 
• 

The front of the display is a shiny black with a fairly thin bezel around the top and sides of the screen, but a very large bezel at the lower half of the display. Perhaps the large bezel at the bottom is necessary to house the electronics and inputs while keeping the overall thin profile, but it causes a couple of issues in my use. The first is that it raises the display up by a few inches compared to if it had no bezel at the bottom. Depending on the height of your desk this might not matter, but for me it puts the display at such a height that I can’t get the angle I want on the display; it makes placement a bit harder and more limited in my experience compared to no bezel.
Another complaint is that the ML248H has LED lit controls that are touch sensitive buttons, but they’re annoying to use in practice. The labels of the buttons disappear until you hit a button to light them up, but that also causes a menu to pop up on the screen. Since you can’t see which menu option you’re selecting until after you touch the panel, you almost always have to back out of that initial menu and then pop up the correct one. Having the initial touch just light up the buttons and the second touch pop up the menu would be far more user friendly. I’m still a fan of actual buttons over touch sensitive ones for my display adjustments as well, but that would ruin the look of the ASUS. On the bright side, the buttons are accurate in responding to touches and I didn’t find myself having to hit them repeatedly to get them to respond.
The one final issue caused by using such a thin display is that the monitor can’t use a standard IEC cord but instead has an external power brick that you will now have to hide away as well. I’m sure most people won’t have an issue hiding the cord and adapter away, but it does make for more of a wiring mess than a typical IEC power cord would.
Here’s an overview of the full display specs:

ASUS ML248
Video Inputs	HDMI 1.3, D-sub
Panel Type	TN
Pixel Pitch	0.2768 mm
Colors	16.7 Million
Brightness	250 nits (Typical)
Contrast Ratio	1,000:1 (Typical)
Response Time	2 ms (GTG)
Viewable Size	24"
Resolution	1920x1080 at 60 Hz
Viewing Angle	170 degrees horizontal, 160 degrees vertical
Backlight	LED
Power Consumption (operation)	< 30 W
Power Consumption (standby)	< 1W
Screen Treatment	Antiglare with hard-coating 3H
Height-Adjustable	No
Tilt	-5 degrees to +20 degrees
Pivot	No
Swivel	-20 degrees to +20 degrees
VESA Wall Mounting	Yes: 100 mm x 100 mm
Dimensions w/ Base (WxHxD)	572mm x 431mm x 221mm
Weight	9.04 pounds with stand
Additional Features	Headphone Jack (rear)
Limited Warranty	3 Years Limited Parts and Labor
Accessories	Power adapter, VGA cable, HDMI to DVI Cable
Price	$200

OSD Menus

Gallery: ASUS ML248H OSD Menus

• 
• 
• 
• 
• 
• 

The OSD menus for the ASUS are pretty well designed overall. The touch sensitive buttons are well spaced and respond well to touches, so you don’t have to hit them multiple times to get an input or worry if you’re hitting the correct one. The main issue, as noted above, is that since the labels for the buttons are hidden until you actually press a button, and you don’t know which one to hit for the menu until you actually try one. That might put you into the brightness or contrast adjustments, and then you have to navigate back out into the main menu. I wish the labels would either stay illuminated (well, that might be a different sort of annoying), or better would be to have the first touch light up the menus instead of selecting an option.